AVR335 harman/kardon
MAIN REMOTE CONTROL FUNCTIONS
been pressed so that AUTO appears in the on-bypass mode with true, fully analog, two-channelbetween 01 and 30 that you wish to assign to the
screen menu and Lower Display Lineo, pressingleft/right stereo mode with no surround processing orstation. (See page 32 for more information.)
and holding either of the buttons for 3 seconds willbass management, as opposed to other modes where
Y Delay/Prev Ch.: Press this button to begin
cause the tuner to seek the next station with acceptabledigital processing is used. When the button is pressedthe process for setting the delay times used by the
signal strength for quality reception. When MANUALso that SURROUND OFF appears in the LowerAVR 335 when processing surround sound. After
appears in the Lower Display Lineo, pressing theseDisplay Lineo, you may enjoy a two-channel pres-
buttons will tune stations in single-step increments. (Seeentation of the sound along with the benefits of basspressing this button, the delay times are entered by
page 31 for more information.)management. Depending on whether your system ispressing the Set Button p and then using the
configured for 5.1 or 6.1/7.1 channels, the next press�/UButtonsnto change the setting.Press the
v OSD Button: Press this button to activate theSet Button p again to complete the process.
On-Screen Display (OSD) system used to set up orof the button will cause either 5 CH STEREO or(See page 24 for more information.)
7 CH STEREO to appear, and the stereo signal
adjust the AVR 335Os parameters.will be routed to all five (or seven) speakers. (SeeZ Speaker Select: Press this button to begin
w Dolby Mode Selector: This button is used topage 29 for more information on stereo playbackthe process of configuring the AVR 335Os bass man-
modes.)
select from among the available Dolby Surround pro-agement system for use with the type of speakers
cessing modes. Each press of this button will selectS DTS Neo:6 Mode Select: Press this button toused in your system. Once the button has been
one of the Dolby Pro Logic II modes or Dolby 3select a DTS Neo:6 mode. These modes take a two-pressed, use the �/U Buttons n to select the
Stereo. When a Dolby Digital-encoded source is in use,channel you wish to set up. Press the Set Button
the Dolby Digital mode may also be selected. (Seechannel stereo- or matrix surround-encoded sourcep and then select another channel to configure.
and create a full five-, six- or seven-channel sound
page 29 for the available Dolby surround modefield. (See page 29 for the available DTS Neo:6When all adjustments have been completed, press
options.)options.)the Set Button p twice to exit the settings and
return to normal operation (see page 16).
x DTS Digital Mode Selector: When a DTS-T Macro Buttons: Press these buttons to store or
encoded digital source is selected, each press of thisrecall a OMacro�, which is a preprogrammed sequencea Multiroom: Press this button to activate the
button will scroll through the available DTS modes. Theof commands stored in the remote. (See page 37 formultiroom system or to begin the process of changing
specific choice of modes will vary according to whetherthe input or volume level for the second zone. When
or not the source material contains DTS-ES 6.1more information on storing and recalling macros.)used with the DVD player, it controls the Subtitle
Discrete encoding. When a DTS source is not in use,U Disc Skip Button: This button has no directOn/Off function (see page 35).
this button has no function. (See page 29 for the avail-function for the AVR 335 but is most often used tob Volume Up/Down: Press these buttons to raise
able DTS Digital options.)change to the next disc in a CD or DVD player when
the remote is programmed for that type of device.or lower the system volume.
y Logic 7 Mode Select Button: Press this buttonWhen the remote is used to control the AVR, the
to select from among the available Logic 7 surroundVID2/TV device or the VID3/CBL/SAT device, thesec TV/Video Selector: This button does not have a
modes. (See page 29 for the available Logic 7direct function on the AVR 335, but when used with a
options.)buttons are programmed to operate the DVD playerOscompatibly programmed VCR, DVD or satellite receiver
transport controls. However, you may use the Transportthat has a OTV/Video� function, pressing this button will
z Skip Up/Down Buttons: These buttons do notControl Punch-Through feature described on page 39switch between the output of the player or receiver
have a direct function with the AVR 335, but whento program these button to operate another deviceOsand the external video input to that player. Consult the
transport controls when the AVR, VID2 or VID3 device
used with a compatibly programmed CD or DVDhas been selected. (See page 38 for more informationownerOs manual for your specific player or receiver for
changer they will change to the previous disc in thethe details of how it implements this function.
changer or carousel.on using the remote with products other than the
AVR 335.)d 6-Channel/8-Channel Direct Input: Press
` Transport Controls: These buttons do not havethis button to select the device connected to the
any functions for the AVR 335, but they may be V Preset Up/Down: When the tuner is in use,8-Channel Direct Inputs j as the audio source.
programmed for the forward/reverse play operation press these buttons to scroll through the stations (See page 27 for more information.)
of a wide variety of CD or DVD players, and audio programmed into the AVR 335Os memory. When
some source devices, such as CD players, VCRs andWhen you wish to use the 6-Channel/8-Channel
or video cassette recorders. When the remote is cassette decks, are selected using the device InputDirect Input j in conjunction with a video source,
used to control the AVR, the VID2/TV device or the
VID3/CBL/SAT device, these buttons are programmedSelectors e, these buttons may function asyou must first select the video source by pressing one
to operate the DVD playerOs transport controls.Chapter Step or Track Advance.of the Input Selectors e, then press this button to
However, you may use the Transport Control Punch-choose the device connected to the 6-Channel/8-
W Clear Button: Press this button to clear incorrectChannel Direct Input j as the audio source.
Through feature described on page 39 to programentries when using the remote to directly enter a radio
these button to operate another deviceOs transportstationOs frequency.e Mute: Press this button to momentarily silence
controls when the AVR, VID2 or VID3 device has beenthe AVR 335 or TV set being controlled, depending on
selected.X Memory Button: Press this button to enter a radiowhich device has been selected. When the AVR 335
station into the AVR 335Os preset memory. First, tune
R Stereo Mode Select Button: Press this buttonthe desired station, and then press this button. Tworemote is being programmed to operate another device,
to select a stereo listening mode. When the button isunderline indicators will flash at the right side of thethis button is pressed with the Input Selector Button
pressed so that DSP SURR OFF appears in thee to begin the programming process. (See page
Upper Display Line ÷, and within 5 seconds press37 for more information on programming the remote.)
Lower Display Lineo, the AVR will operate in athe Numeric Keys r for the preset number
1212 MAIN REMOTE CONTROL FUNCTIONSMAIN REMOTE CONTROL FUNCTIONS
12 |
ACEC
